V8016 Weight Indicator

Categoría:

Descripción

V8016 Weight Indicator

1.Introduction:

The instrument adopts 24-bit A/D converter, which is combined with various sensors and transmitter to measure, display, monitor, collect and record the physical parameters such as pressure, flow rate, material position, component analysis, force and mechanical quantity.

2. Technical parameters

Work environment Temperature: 0-50℃ Indicator: Double 5-bit high brightness red LED
Moisture:20-90%RH Output voltage: 5v±5%(supply for load sensor),current<50mA
Accuracy ±0.2%F.S Supply voltage: 195~242 Vac, Power<5w;Or 24Vdc
Measurement cycle time 0.2s

3. The key introduction

“Set”: set and confirm the parameter “>”: Shift key or peeling key (for peak meter)

“∧”:add the data “CLR”: Peak reset key or peeling key (for up and down limit instrument)

4.Dimensions

Panel size
L H
160mm 80mm

5.Parameters description

Symbol Name 范 围
SA1 OUT1 relay output 00000~full scale
SA2 OUT2 relay output 00000~ full scale
SA3 OUT3 relay output 00000~ full scale
SA4 OUT4 relay output 00000~ full scale
SL Calibration“0” 00000
SH Load calibration Above half full scale
Sd Display decimal places selected 0~3
Id Division value 0.1,0.2,0.5,1,2
CLTF Tare key selection 0.1
FIL Weight filtering 1 to 9
OUTF Alarm output selection 0 or 1, 0 is alarm when less setting; 1 is alarm when above setting.

6. Operating instructions

6.1 Press “SET” and hold 3 seconds, display “SA1”, press “>”to set out1 relay output value; press “SET”, display “SA2” to set out2 relay output value; press “SET”, display “SA3” to set out3 relay output value; press “SET”, display “SA4” to set out4 relay output value;

6.2 Press “SET”, display “CIN”, Password input, setting “00000” is valid. If you want to keep the password, press “SET”, to set next; if you want to change the password, press “CLR”, display “CON”, to input new password, press “SET”, to set next;

6.3 Press “SET” display “SL”, to set the unload Zero Calibration.

6.4 Press “SET” display “SH”, to set the load calibration (must above half full scale), input the load value.

6.5 Press “SET” display “Sd”, to set Display decimal places, press “∧” to change the decimal places.

6.6 Press “SET” display “Id”, to set Division value, you can press “∧” to choose 0.1,0.2,0.5,1,2.

6.7 Press “SET” display “CLTF”, to set Tare key selection, when “CLTF” is “0”, press “CLR” can tare to the indicator; when “CLTF” is “1”, press “CLR” can’t tare to the indicator.

6.8 Press “SET” display “FIL”, to set Weight filtering, Choose 1-9, the larger the value, the slower the display. This value affects stability. Press “SET” to work station.

6.9 Press “SET” display “OUTF”, to set Alarm output selection, when the 5th digit tube displays “1”, OUT1 relay output signal when the value is above “OUT1” setting value; when the 5th digit tube displays “0”, OUT1 relay output signal when the value is less than “OUT1” setting value; set the 4th,3rd,2nd digit displays to set OUT2, OUT3, OUT4 by the same way.

6.10 Indicator connecting instruction:

Connecting load cell or junction box IN+/IN-:11-green,12-white

Connecting load cell or junction box E+/E-:9-Red,10-Black

Connecting LED data cable.23-blue,24-brown

GND

Supply power

7. Notes

When the indicator display “E1”, it means no connecting the load sensor or the signal of load sensor is too big.

8. Emergency

8.1 When forgot the password, press “CLR” and power on, the password will be recover “00000”.

8.2 When mis-set or the button doesn’t work, press “∧”and power on, the indicator restore factory defaults.

8.3 Press “>” and power on, the digital tube changes between 0 and 1, when display “0”, loose the key, the indicator will be Upper and lower limit instrument; when display “1”, loose the key, the indicator will be peak value instrument;

\\192.168.1.101\公司\产品图片\原图\称重传感器\仪表\V8016\V8016-1.jpg

\\192.168.1.101\公司\产品图片\原图\称重传感器\仪表\V8016\V8016-3.jpg

 

Valoraciones

No hay valoraciones aún.

Sé el primero en valorar “V8016 Weight Indicator”

Tu dirección de correo electrónico no será publicada. Los campos obligatorios están marcados con *

es_ESSpanish
habla con nosotros
habla con nosotros
Preguntas, dudas, problemas? ¡Estamos aquí para ayudarte!
Conectando...
¿Tienes alguna pregunta? ¡Escríbenos!
¿Tienes alguna pregunta? ¡Escríbenos!
:
:
:
¿Tienes alguna pregunta? ¡Escríbenos!
:
:
Esta sesión de chat ha finalizado
¿Ha sido útil esta conversación? Vota esta sesión de chat.
Bueno Malo